Fllanxhë jo standarde
Non-standard flanges will only be used in cases where pressure, temperature and size requirements exceed the capabilities of standard flanges. Keep in mind that non-standard flanges require calculation, design and special manufacturing procedures, which is why they are chosen only as a last resort. The most common such applications are large equipment flanges and heat exchangers body flanges.
Non-standard flanges are designed and calculated according to ASME VIII Div.1 Appendix 2 and Appendix S, and according to ASME VIII Div.2 part 4.16.
Design criteria
Rules for the design of bolted flange connections as described in Div.1 Appendix 2 apply to flanges with gaskets placed entirely within the circle enclosed by the bolt holes and with no contact outside this circle.
This method is applicable to circular flanges under internal pressure and takes into account only hydrostatic end loads and gasket seating loads. Rules have been further modified so that they can be applied to the design of flanges under external pressure, reverse flanges and flanges with nut stops.
Design procedure for large diameter, low pressure flanges shall be supplemented by methods other than the code e.g.: check flange rotation. Flanges greater than 60 inches (1524 millimeters) inside diameter and designed for up to 100 psig (689 KPa) pressure fall under this category.
Madhësia
Fllanxhë jo standarde: 1/4 ″ -160
DN8-DN4000
MATERIALE:
Çeliku i karbonit: ASTM A105, ASTM A105N, GB 20, C22.8.
Çelik aliazh: ASTM / ASME A182 F1-F12-F11-F22- F5-F9- F91
Çelik inox: ASTM / ASME A182 F304-304L-304H-304LN-304N
ASTM / ASME A182 F316-316L-316H-316LN-316N-316Ti
ASTM / ASME A182 F321-321H, F347-347H
Çeliku me temperaturë të ulët: ASTM / ASME A350 LF2.
Çelik me performancë të lartë: ASTM / ASME A694 F42, F52, F56, F60, F65, F70
Lloji i ballafaqimit me fllanxhë
Seritë Amerikane: Fytyrë e sheshtë (FF), Fytyrë e ngritur (RF), Gjuha (T), Groove (G), Femër (F), Mashkull (M), Fytyra e nyjeve të tipit unazë (RJ / RTJ)
Seritë e Evropës: Type A (Flat Face), Type B (Raised Face), Type C (Language), Type D (Groove), Type E (Spigot), Type F (Recess), Type G (O-Ring Spigot), Lloji H (Gryka e Unazës O)
Presioni
Seritë Amerikane: Klasa 150, Klasa 300, Klasa 600, Klasa 900A, Klasa 1500, Klasa 2500.
Seritë e Evropës: PN2.5, PN6, PN10, PN16, PN25, PN40, PN63, PN100, PN160, PN250, PN320, PN400.
STANDARDI
Fllanxha jone standarde mund të prodhohet bazuar në standardin e përbashkët dhe të bëjë disa ndryshime në përputhje me kërkesat e klientëve tanë.
ASME ANSI B16.5, ASME ANSI B16.47.
API 605, API 6L.
MSS SP 44
CSA Z245.12
EN1092-1, EN1759-1.
DIN2630, DIN2631, DIN2632, DIN2633, DIN2634, DIN2635, DIN2636, DIN2637, DIN2638.
BS1560, BS 4504, BS 10.
AFNOR NF E29-200-1
ISO7005-1
AS2129
JIS B2220
UNI 2276. UNI 2277.UNI 2278 .UNI 6089 .UNI 6090
Proceset industriale
Vdesin falsifikim, Machining.
Aplikimi për fllanxhë jo standarde
Gaz natyror, kimik, naftë, ndërtim anijesh, detare, prodhim letre, metalurgji, elektricitet, energji, kazan, etj.
